Wollte nur der Vollständigkeit halber die Bilder der fertigen Adaption posten...
MFG
und
Schöne Ostern
Wollte nur der Vollständigkeit halber die Bilder der fertigen Adaption posten...
MFG
und
Schöne Ostern
Hallo,
habe die Pinbelegung samt schematic vom Sucher von einem freundlichen JVC - Techniker erhalten.
Grüsse
Ingmar
Bitte die Beitragsschablone sorgfältig ausfüllen.!!
Hersteller: JVC
Modell: VF-P115
Fehler: kein
Bereits durchgeführte Tests und Vorarbeiten:
Kennt jemand die Pinbelegung des 6pol. TMW-Steckers vom JVC - Camcordersucher VF-P115 bzw. VF-P116?
Dieser Sucher passt auf die Camcorderserie GY-DV5xx bzx 5xxxx von JVC.
Benötige das Pinout (+12V, GND, Video, VideoGnd, TALLY, REC, Batt.)
Vielleicht hat auch jemand Zugriff auf das Schematic des GY-DV5000 Camcorders.
Ich will nämlich einen Sony Studiosucher an den Camcorder anschliessen und mir den Steckeradapter selber bauen. (ist bezahlbarer...)
Hallo Uwe,
vielen Dank für den Tip, daran hätt ich natürlich wieder nicht gedacht mal nach einem Sample zu fragen. Mal sehen was daraus wird.
Grüsse
Ingmar
Hallo,
suche einen Lieferanten für einen LI-ION Ladereglerbaustein (s.Bild)
Bauteilstempel "LTLX" Bauteilbezeichnung "LTC1733" aus einer Bluetooth GPS Mouse.
Nedis, Aswo-Espio, Spoerle udgl. Fehlanzeige. Bei Digikey ist er zwar gelistet - habe dort aber leider keinen account.
Vielleicht hat jemand eine Idee wo man das Teil in geringer Stückzahl (so 1-2) bestellen kann, so ganz normal per NN oder Rechnung und OHNE Kreditkarte.
LG
Ingmar
Hallo,
der Ordnung halber schliesse ich den thread (ein bisschen spät) jetzt noch ab:
Die maz war ein PANASONIC NV-G40 und die Position der Diode war (D12) auf dem pcb und im schematic D1012 (MA220DB) eine 20V Zenerdiode.
Diode 1,3W20V getauscht, Elko C1017 erneuert 680uF/35V - getestet - und wieder raus zum Kunden.
WÜNSCHE ALLEN EINEN GUTEN START INS JAHR 2006, VIEL GLÜCK UND GESUNDHEIT!!
Ingmar
Vielen Dank Rüdiger,
ist angekommen
Ingmar
so, hab jetzt mal schnell ein paar Bildchen gemacht (leider nur Handybilder)...
guten Morgen ...
ähhem ... bitte
Gruss Ingmar
stell gleich morgen ein bild rein...
gruss
Ingmar
hallo,
ich hab leider nur das netzteil vom "kunden" bekommen.
der kunde hat die gerätebezeichnung "panasonic NV-640HQ" auf das schirmblech geschrieben. - mehr infos hab ich leider nicht.
die pos. nummern auf dem netzteilprint sind allerdings alle nur zweistellig...
auf er netzteilplatine steht ist noch "VEP01338A" aufgedruckt, sowie ein Aufkleber auf dem Schirmblech" VEK3702"
Bitte die Beitragsschablone sorgfältig ausfüllen.!!
Hersteller: Panasonic
Modell: NV-640HQ
Fehler: Netzteil Diode D12 defekt
Hallo,
ich suche den Wert der Zenerdiode (D12) - vielleicht hat jemand den Schaltplan zur Hand
grüsse
Ingmar
Hallo,
danke für den Tip, soweit ich mich erinnern kann, hab ich das IC damals auch getauscht - ist schon einige Zeit her
PS.: Wenn ich mich nicht irre, kennen wir uns - zumindest über Telefon - haben vor einiger Zeit mal über die Focusregler von den MCM2102 ...
Grüsse
Ingmar
meinst du den JVC GR-DYX10 camcorder?
hab hier einige infos gefunden die du versuchen könntest:
(infos von:http://hardware.mcse.ms/archive60-2004-6-27259.html)
THE SOLUTIONS
Solution #1: Cold Reset
The reason it tells you to REMOVE AND REATTACH BATTERY is not that the
battery is bad, but that removing all sources of energy (battery and power
cord) causes a COLD RESET. When you use the unit's on/off switch, parts of
the camera are still receiving power and so you do not get the benefits of a
COLD RESET. Just like your car; turning the ignition off will still power
the clock and radio. You have to completely remove all power. If you are
lucky, the camera will reset itself and start working again.
Solution #2: Awareness of Humidity
It seems older units would issue the same SAFEGUARD MODE error message for
more than one problem. For example, older units do not tell you that they
are shutting down for an hour because they detected high condensation, or
moisture. So you play with the camera, remove the battery, reattach it,
remove the tape, reinsert it, stand on your head, pray to your god, go to
the bathroom, and voila! The camera is working again. It was nothing you
did, just that the humidity went down enough for the unit to start working
again. So consider high humidity as a possible source of the problem. If it
is a rainy day, or you are near the sea, you might never get it to work that
day in that location.
Solution #3: Head Cleaning
If you have never used a head-cleaning tape on your camcorder, you might
give that a try. Mine has come back to life a few times by doing just that.
Just don't do it too many times in a row because you can permanently damage
the head. Read the instructions.
So we have covered a few reasons why these errors come and go as if by
magic. They are intermittent and recurring. The camera will appear to work
at times, and the next minute it shuts down.
Solution #4 : Fake Solutions
Another reason why the problems come and go is that, as several technicians
have reported, the problem can be a loose connector inside. That is why some
people report that tapping the camera gently or rocking it side to side has
brought it back to life. Some have gone as far as putting cardboard between
the tape door and the tape mechanism in order to exert pressure and keep the
camera working. I can only warn you that these kinds of "repairs" are
temporary and likely to damage the unit further. Control your anger!
Solution #5: Compressed Air
On some models, there is no shield covering the many delicate electronic and
moving parts in the tape mechanism when you open it to replace the tape. A
piece of dirt, grain of sand, or other debris can get caught in the tiny
gears and stop movement or throw them off alignment. You can explore this
possibility by getting a can of compressed air at any computer shop and
blowing it into the inside of the camera. Follow the instructions, keeping
the air nozzle however many inches away from the target as they say.
Practice on some other object first, because if you tilt the can or hold it
too close to the target you can freeze the target and do more damage than
good. This applies to fingers too!
Solution #6: Tape Age, Brand, and Type
Have you tried using a brand new tape? Or only your really old ones? Try a
new tape.
Now for the controversial issue of what brand of tape to use. Controversial
because JVC's own Stacy Sample, Service Coordinator for JVC in Houston, TX
says that "TDK and Maxell tapes tend to be two brands that are very
problematic in our digital line wherein Panasonic, JVC and Fuji seem fine.
We just find that TDK has the most problems, Maxell is a close second and
Sony is 50% of the time. The others I mention rarely have a problem." Why
JVC does not make this information available when you purchase the unit or
visit their many websites is beyond me.
A different point of view I ran into is. Yes, there is an issue, but it has
nothing to do with the brand, but with the tape type. There are MP and ME
tapes. These two types use different particles, and different lubrication.
The two lubricating materials form some sort of goo when mixed together, if
you use both types of tape in the same unit. So as long as you don't mix
tapes of different types, they will work just fine in your camcorder. Some
refer to these types as "dry" and "wet", but I don't know which is which. In
any case, it is not known (to me) how accurate this point of view of not
mixing tape types is.
Solution #7: Do not store tape in unit
Because of the delicate nature of the miniDV mechanism, do not store the
unit with a tape inside. The theory is that a loaded tape will put pressure
on parts of the mechanism and increase the chance that parts will stick
together, making the tape harder to be pulled by the motor, causing the
SAFEGUARD error.
Solution #8: Send in for Service
Let us say you have tried all of the above and your camera still will not
work. Now you have to decide whether to send the camera in for repair or
not. My JVC camcorder, model GR-DVM90, turns out to be the model that most
frequently suffers from these problems. For that reason, I am not having the
camera serviced and instead taking JVC to court in a class-action lawsuit,
which you are welcome to join free of charge and with no obligation.
habs mir jetzt nochmal genauer angesehen - thx tcfkcat - genau der pin für die instrumentenbeleuchtung wurde bei beiden geräten anscheinend "rausgezwickt" oder zumindest so gekürzt, dass der isostecker an dem pin keinen kontakt mehr hatte.
anscheinend wollte hier jemand etwas umbauen - oder die werkstatt testen - wer weiss.
hab zwei buchsen aus schlachtradios gespendet und siehe da - klappt
die Hintergrundbeleuchtung des lc-displays sollte doch eigentlich immer funktionieren auch wenn die Armaturenbel. nicht an ist. Denn ohne Beleuchtung ist nur schemenhaft zu erkennen welchen Track man grade abspielt ...
Hab so ziemlich alle Anschlusswarianten getestet - aber kein Licht ( am dislay)
soviel sich erkennen kann, sind immer mehrere Glühlämpchen in Serie geschaltet und diese dann an den Collector eines SMD -Transtistors.
es ist schwierig die Schaltung nachzuverfolgen ...
Bitte die Beitragsschablone sorgfältig ausfüllen.!!
Hersteller: Blaupunkt
Modell: Florida RD 168, Grenoble RD169
Fehler: keine Bedienteilbeleuchtung obwohl alle Glühlampen ok.
Bräuchte fir die beiden Geräte die Schaltpläne...
Vielleicht kann jemand helfen
Grüsse
Ingmar
so, es ist geschafft.
hab das signal bis zur videoendstufe verfolgt - war alles bestens, liess sich auch schön regeln.
nur am collector der videoendstufe (mpsw42) war nix mehr sinnvolles zu messen. (foto1)
am 2.foto ist das schirmbild mit fehler zu sehen.
hab dann als ersatz einen BF819 eingebaut (hatte nix anderes am lager) und siehe da das videosignal steht am collector so an, wie ichs mir vorgestellt habe.
(foto3)
und auch das schirmbild sieht ganz gut aus.
die fotos haben nicht die beste qualität - sind nur mitn handy gemacht.
HeiGru: auf dem Board sind lediglich Regler für die Geometrie vorhanden. Keine Regler Subbright udgl. -
Geh jetzt mal mit dem Osci das videosignal verfolgen ...
hin war ein 68nF MKT Kondensator in der Horizontalabl. (der hatte Kapazitätzverlust). infolge ging ein LT1085 Spannungsregler in die Knie, der die +B für den Hochspannungstransformator regelt. (ca. 16V)
Der Monitor wird generell mit 24VDC versorgt.
nach erneuern des Kondensators und des Spannungsreglers war die Bildgeometrie wieder in Ordnung.
Die Bildhelligkeit sowie auch der Kontrast lässt sich über die externen Potis regeln.
Beim Kontrast tut sich bist zum mittenanschlag des Potis nix - nach ca. 50% des Einstellwinkels kann ich ihn soweit hochregeln bis vom balkensignal der weisspegel und der erste graupegel zu sehen sind.
selbst wenn ich die ug2 hochdrehe sind keine weiteren balken zu sehen. das gesamte bild wird einfach heller.